Tronex^® Cutting Tools

What makes Tronex^® Cutting Tools the best in the world?

Special Manufacturing and Design

high-grade alloy steel
cutting edges induction hardened to
63-65 Rockwell C
each cutter is tested individually
distinctive “snap” cutting performance
ESD safe grips
grips are cushioned

**** Quality Assurance

All Tronex^® tools are checked individually before they leave the factory. Each cutter must cut and cut well! As a final measure, Tronex warrants every tool to be free of defects in materials and workmanship for the life of the tool. Tronex^® cutters are manufactured **** in the USA.

3 Types of Cutting Edges Available

Semi Flush
Cutting edges have a slight bevel, which produces cuts with a small pinch on the tip of the cut wire. Longest cutting life.

Flush
Cutting edges have a minimum bevel, which produces cuts with a very small pinch.

Razor Flush™
Cutting edges have no bevel, which produces cuts with no pinch on the tip of the cut wire.
Reduced cutting life.

What is “Razor Flush™”?
It is grinding cutting edges to razor sharpness. When cutting wire, no raised area or pinch is left on the cross section. The leads are subjected to minimum shock during razor flush cutting. Next, Razor Flush™ means a fine set screw stop is built into the handle or jaw of the cutter to prevent the exceptionally sharp edges from dulling themselves after the cut is completed. The set screw can be adjusted when the cutter is sharpened.

Tool Lengths
are measured from top of cutter head to bottom of handle “Short” grips (far left) are ~115mm (4.53") long and “Long” grips are ~140mm (5.5") long.

Exceptionally Sharp, Hard and Tough Cutting Edges
They are made by using a proprietary dual sharpening process, then raised to optimum hardness and toughness through a specialized induction heating and tempering system

Ergonomic Handles
A cutting tool is deemed ergonomic if it materially contributes to reducing the probability of cumulative trauma disorders with the hand, finger, wrist, or arm. The Tronex^® 7000 Series handle is designed for transferring force from the operator to the point of operation in a highly ergonomic manner. The average American worker's hand or palm is approximately four inches wide; therefore, tool handles should be four inches long at least. To allow freedom of hand placement, 4 to 5 inches would be even more desirable. The length of the Tronex^® 7000 Series handle, from the joint to the end, is 4.8 inches. In contrast, handles from competition cutters are only 3.6 to 3.7 inches. The Series 7000's long handle forces the operator to spread the cutting force with use by all four fingers to operate the tool. Operators may use only two or three fingers on cutters with shorter handles. The longer handle also spreads the cutting load over the width of the palm in a bar of force. In contrast, a short handle presents a point of force which digs into the palm, compressing nerves and tendons and reducing blood flow.

ESD Safe Grips
The Tronex^® 7000 features, as standard, a unique double-sheathed, ESD safe, cushioned grip. The inner sheath is a tough vinyl, ESD safe material which holds the leaf spring and the cushioned surface to the cutter handle. The outer sheath, also ESD safe, provides a no-slip, cushioned surface for the operator's hand. This is important because the slight compressibility of the cushion aids to distribute the cutting pressure more effectively. It can even absorb sharp particles which could be imbedded in the hand. The Tronex^® 7000 cushion grip is almost always considered by operators to be more comfortable than the hard, plastic used by competitors.

Oval Head Cutter

Oval Head Cutters are strong, versatile and long-lasting, this most popular shape can be used for many applications. Designed to be durable through hundreds of thousands of cuts. Options: regular and large style; with short or long handles; with relief head or standard.

E= Overall Length

Oval Head
	Short Handle	Long Handle
A	11.1mm	11.1mm
B	6.9mm	6.9mm
C	8.4mm	8.4mm
D	1.0mm	1.0mm
E	115mm	140mm
F	74°	74°

Large Oval Head
	Short Handle	Long Handle
A	13mm	13mm
B	6.9mm	6.9mm
C	10.7mm	10.7mm
D	1.2mm	1.2mm
E	117mm	142mm
F	74°	74°

Miniature Oval Head
	Short Handle	Long Handle
A	9.1mm	9.1mm
B	6.9mm	6.9mm
C	6.1mm	6.1mm
D	0.9mm	0.9mm
E	113mm	138mm
F	74°	74°

Ordering Information and Wire Diameter Capacity


Oval, Short Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire			Unit
7110	Oval, Short Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7146	Oval, Short Handle, Flush Cutter	.15to 1.10 mm	.006to .045 in	each
7180	Oval, Short Handle, Razor Flush Cutter	.10to 1.00 mm	.004to .039 in	each

Oval, Long Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7130	Oval, Long Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7162	Oval, Long Handle, Flush Cutter	.15to 1.10 mm	.006to .045 in	each
7206	Oval, Long Handle, Razor Flush Cutter	.10to 1.00 mm	.004to .039 in	each


Oval Relief, Short Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7112	Oval Relief, Short Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7148	Oval Relief, Short Handle, Flush Cutter	.15to 1.10 mm	.006to .043 in	each
7182	Oval Relief, Short Handle, Razor Flush Cutter	.10to 1.00 mm	.004to .039 in	each

Oval Relief, Long Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7132	Oval Relief, Long Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7164	Oval Relief, Long Handle, Flush Cutter	.15to 1.10 mm	.006to .043 in	each
7208	Oval Relief, Long Handle, Razor Flush Cutter	.10to 1.00 mm	.004to .039 in	each


Large Oval, Short Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7114	Large Oval, Short Handle, Semi-Flush Cutter	.20to 1.50 mm	.008to .059 in	each
7150	Large Oval, Short Handle, Flush Cutter	.15to 1.50 mm	.006to .059 in	each
7184	Large Oval, Short Handle, Razor Flush Cutter	.10to 1.30 mm	.004to .051 in	each

Large Oval, Long Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire			Unit
7134	Large Oval, Long Handle, Semi-Flush Cutter	.20to 1.50 mm	.008to .059 in	each
7166	Large Oval, Long Handle, Flush Cutter	.15to 1.50 mm	.006to .059 in	each
7210	Large Oval, Long Handle, Razor Flush Cutter	.10to 1.30 mm	.006to .051 in	each


Large Oval Relief, Short Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire			Unit
7116	Large Oval Relief, Short Handle, Semi-Flush Cutter	.20to 1.40 mm	.008to .055 in	each
7152	Large Oval Relief, Short Handle, Flush Cutter	.15to 1.50 mm	.006to .059 in	each
7186	Large Oval Relief, Short Handle, Razor Flush Cutter	.10to 1.30 mm	.004to .051 in	each

Large Oval Relief, Long Handle

Prod #	Description	Diameter of Soft Copper Wire		Unit
7136	Large Oval Relief, Long Handle, Semi-Flush Cutter	.20to 1.40 mm	.008to .055 in	each
7168	Large Oval Relief, Long Handle, Flush Cutter	.15to 1.50 mm	.006to .059 in	each
7212	Large Oval Relief, Long Handle, Razor Flush Cutter	.10to 1.30 mm	.004to .051 in	each


Miniature Oval, Short Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7122	Miniature Oval, Short Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7158	Miniature Oval, Short Handle, Flush Cutter	.10to 1.00 mm	.004to .039 in	each
7192	Miniature Oval, Short Handle, Razor Flush Cutter	.10to 0.80 mm	.004to .031 in	each

Miniature Oval, Long Handle Cutters

Prod #	Description	Diameter of Soft Copper Wire		Unit
7142	Miniature Oval, Long Handle, Semi-Flush Cutter	.20to 1.20 mm	.008to .047 in	each
7174	Miniature Oval, Long Handle, Flush Cutter	.10to 1.00 mm	.004to .039 in	each
7218	Miniature Oval, Long Handle, Razor Flush Cutter	.10to 0.80 mm	.004to .031 in	each